Dairy farming is a class of agricultural Cheap Blake Comeau Jersey , or an anima to the feed to increase quality milk production.
Keeping milk cool helps preserve it. When windmills and well pumps were invented, one of its first uses on the farm besides providing water for animals was for cooling milk, to extend the storage life before being transported to the town market. The naturally cold underground water would be continuously pumped into a tub or other containers of milk set in the tub to cool after milking. This method of milk cooling was extremely popular before the arrival of electricity and refrigeration.
When refrigeration first arrived (the 19th century), the equipment was fairly small and did not have the ability to rapidly cool the large volume of milk that was entering the storage tank in a short period of time. This problem was resolved through the development of the ice bank. This is a double-walled tank design where water and cooling coils fill the space underneath and around the milk tank above.
All day long Cheap John Klingberg Jersey , the small compressor and cooling system slowly draws heat out of the water, while a second pump continuously circulates the water around the coils. Ice eventually builds up around the coils, until it reaches a thickness of about three inches surrounding each pipe, and the cooling system shuts off. When the milking operation starts only the milk agitator and the water circulation pump blowing water across the ice and the steel walls of the tank are needed to rapidly reduce the incoming milk to a temperature below 40 degrees. But because the ice is not permitted to build up until it touches the milk storage tank, the milk does not get cold enough to also freeze.
This cooling method worked well for smaller dairies up to about 40 cows Cheap Tyler Seguin Jersey , but for large numbers of animals a better system was needed to rapidly cool the incoming warm milk. This is usually done using a device known as a plate chiller, which is a heat exchanger. Alternating stainless steel plates cause the milk to flow in a thin sheet across the plates, while cold water is circulated in a thin sheet on the other side of the plates. Flattening out the milk flow permits quick. even cooling for all the milk, compared to a round tube where the center core does not cool as rapidly as the walls.
The plate chiller has high cooling demands, and for many farms this involves a step back into the past Cheap Jamie Benn Jersey , back to the days of windmills and milk-can cooling, except now a large volume of naturally cold underground water is continuously streamed through the plate chiller to quickly bring the milk down to the temperature of the underground water at about 50 掳F (10 掳C). The water is usually not just dumped back into the ground again, but reused for washing and other purposes.
But the milk still is not as cold as it needs to be, so the milk storage tank is still used to do further cooling, to bring the milk down to 40 degrees. But with the development of high-power 3-phase electrical service Wholesale Dallas Stars Jerseys , ice-bank chillers are typically no longer used. Instead the milk storage tank is a direct-cooling system with cooling coils embedded in the walls of the tank, that quickly pull the heat out and dump it across a large array of possibly several different high-horsepower compressors and condensing units. Once the milk has achieved 40 掳F (4 掳C) after milking is finished, only one or two cooling units need to run occasionally to maintain the correct temperature.
Milking machines are held in place automatically by a vacuum system that draws the ambient air pressure down from 15 to 21 pounds of vacuum. The vacuum is also used to lift milk vertically through small diameter hoses, into the receiving can. A milk lift pump draws the milk from the receiving can through large diameter stainless steel piping, through the plate cooler Wholesale Stars Jerseys , then into a refrigerated bulk tank.
Milk is extracted from the cow's udder by flexible rubber sheaths known as liners or inflations that are surrounded by a rigid air chamber. A pulsating flow of ambient air and vacuum is applied to the inflation's air chamber during the milking process. When ambient air is allowed to enter the chamber, the vacuum inside the inflation causes the inflation to collapse around the cow's teat, squeezing the milk out of teat in a similar fashion as a baby calf's mouth massaging the teat. When the vacuum is reapplied in the chamber the flexible rubber inflation relaxes and opens up, preparing for the next squeezing cycle.
It takes the average cow three to five minutes to give her milk. Some cows are faster or slower. Slow-milking cows may take up to fifteen minutes to let down all their milk. Milking speed is only minorly related to the quantity of milk the cow produces -- milking speed is a separate factor from milk quantity; milk quantity is not determinative of milking speed. Because most milkers milk cattle in groups, the milker can only process a group of cows at the speed of the slowest-milking cow. For this reason Cheap Dallas Stars Jerseys , many farmers will cull slow-milking cows.
NFF - Neuendorfer Füchse Forum
Thema drucken
02.11.2019 10:08
Antworten
